E3C-VS1G OMRON PDF

Small Spot/Mark (Separate Amplifier) Extremely thin beam ideal for detection of minute objects and marks. Order Omron Automation and Safety E3C-VS1G (ZND) at DigiKey. Check stock and pricing, view product specifications, and order online. Omron E3C-VS1G Photoelectric Sensor 10mm for E3C Amplifier: : Industrial & Scientific.

Author: Gogore Ket
Country: Guadeloupe
Language: English (Spanish)
Genre: Career
Published (Last): 11 February 2015
Pages: 319
PDF File Size: 16.38 Mb
ePub File Size: 12.24 Mb
ISBN: 166-4-77960-508-4
Downloads: 13186
Price: Free* [*Free Regsitration Required]
Uploader: Tezahn

Do not use pliers, otherwise the connector may be damaged. As a general rule, wire the Sensor in a separate system, use an independent metal conduit, or use shielded cable. However, if the workpieces are close to the Photoelectric Sensors, light from the adjacent Emitter may be received and cause the Sensor to change to the incident light state.

OMRON Products – Scattergood & Johnson

Do not use it for such purposes. To maintain the fiber characteristics, make sure that the lock is released before removing the fibers. Use a soft, dry cloth to clean the Sensor. This information by itself is not suf? If the Sensor and the load are connected to separate power supplies, turn Imron the Sensor power before turning ON the load power. When in doubt, special model numbers may be assigned to?

Precautions for Safe Use To ensure safety, always observe the following precautions. Cable diameter Less than 4 mm 4 mm or greater Tensile strength 30 N max. Be sure to connect or disconnect the connector after turning OFF the Sensor. Insert a capacitor, etc. This is because the Sensors may affect each other and cause output chattering even if separated by more than the Sensor sensing distance. Values Given in Typical Examples The data and values given as typical examples are not ratings and performance and do not indicate specified performance.

  E5CC RX2ASM 800 PDF

Typical examples include the minimum sensing object, engineering data, step height detection data, and selection list for specifications. Be sure to insert a load when connecting the power supply. Light may enter even if the Sensors are separated by more than the sensing distance. Type of noise Noise intrusion path and countermeasure Before countermeasure Noise enters from the noise source through the frame metal.

Precautions for Correct Use Do not use the product in atmospheres or environments that exceed product ratings. If the Sensor does not operate, check the following points. Any exceptions to this rule are indicated in Safety Precautions in individual product information. Secure the connector cover by hand. Please notify us before copying or reproducing this catalog in any manner, for any other purpose.

Omron E3c-vs1g E3CVS1G Photoelectric Sensor Switch

Nuclear e3c-bs1g control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. The lens, case, and fiber covering are made of plastic, so this setup cannot be used if there is a possibility of contact with solvents that will corrode or degrade e. M8 and M12 Connectors? Insert a shield copper plate between the Sensor and the noise source e.

Keep organic solvents away from the Sensor. Fiber insertion mark Fiber 9mm 2 Removing Fibers Open the protective cover, lift up the lock lever, and pull out oron fibers.

  JEFF SOLHEIM CEN REVIEW PDF

Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. The Reflector cannot be mounted if there is any oil or dirt remaining. Lock and unlock the fibers at e3c-va1g ambient temperature of? Power line Work Required for Unconnected Leads Unused leads for self-diagnosis outputs or other special functions should be cut and wrapped with insulating tape to prevent contact with other terminals.

For the E3S-C, the optical axis and the mechanical axis are the ee3c-vs1g, so the optical axis can be easily adjusted by aligning the mechanical axis. The lens, however, is plastic.

Hold the connector cover to connect or disconnect the connector. Separation from High Voltage Wiring Method Do not lay the cables for the Sensor together with high-voltage lines or power lines. Separate Sensors to distance where interference does not occur. In no event shall responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

Strong, conductive electrical wire 2 x 0. Insert a capacitor e. Through-beam Sensors Reflective Sensors 1 If Sensors are mounted in close proximity, use Sensors with the interference prevention function. These Sensors are designed for use in applications for sensing workpieces and workers that do not affect safety.

They are rather values from samples taken from production lots, and are provided lmron reference as guidelines.