BREEZEMAX EXTREME 5000 PDF

BreezeMAX Extreme is part of the carrier-class, field proven BreezeMAX product family and is the first wireless broadband solution to bring WiMAX 16e. BreezeMAX® Extreme WiMAX™ 16e pioneer for the license-exempt market WiMAX 16e for the License-exempt Market Main Features and Highlights. BreezeMAX Extreme is part of the carrier-class, field-proven BreezeMAX product family and brings WiMAX 16e technology to the 5 GHz license-exempt.

Author: Nimi Tojataxe
Country: Swaziland
Language: English (Spanish)
Genre: Relationship
Published (Last): 23 June 2013
Pages: 136
PDF File Size: 13.63 Mb
ePub File Size: 12.59 Mb
ISBN: 307-5-45223-544-9
Downloads: 29864
Price: Free* [*Free Regsitration Required]
Uploader: Yozshulkree

CS to ensure management of the bridged BTS b. Multi-host support behind a single CPE might not work. When performing backhauling over Extreme CPE i. After switching between Operation Modes e. Base Station ID configured in each channel must be unique in the entire network.

Please note that applying factory defaults will not change Country Code selection. When deploying a multi sector site it is recommended using a beezemax high profile GPS antenna kit along with GPS chaining cable CAT5e cable between the base-station on the same site. The Ethernet port supports only Auto Negotiation mode.

Update the Service Profile type per your needs e.

BreezeMAX Extreme | WiMAX technology 5 GHz license-exempt solution

After link with BTS is established, the new version is Set as main automatically by the extremf Radiator verified with version 4. Due to the requirements of FCC regulations, starting with release 1. To refrain from unexpected network behavior it is recommended to set parameters to match the capabilities of the target downgrade version e.

The CPE will provision the services according to the order in which they are received until the license is exceeded.

  HL MENCKEN PREJUDICES PDF

Backhauling link must be under Eth. Note that these can be overcome with additional scripts and configuration of the default installed Radiator AAA: Update the desired Multiple Service Flows with the new service interface you have created.

Recovery actions in case Breezemmax was upgraded to 1. NE failure when provisioning a capacity limit CPE model with services sum exceeding the capacity limit. In very rare occasions, the logical BS ID might be reinitiated.

You may need to breezdmax timers or other logic scripts in the AAA to close these sessions. Known Issues and Limitations With Release 1. There is no issue observed with Ping messages of length up to 14K bytes. Although mentioned in recommendation 20, when operating in release 1.

Under GPS chaining, when there is a faulty chaining cable, the radio units in the chain may not initiate transmission. The documentation includes the following: Such DSCP values might interfere with the feature.

Due breezemxx FCC regulation requirements, starting with release 1. Cable to mains is NOT included and should be ordered separately.

BreezeMAX ® Extreme 5000

Software version integrity on the BTS solved starting with upgrade to version 1. Recommended workaround is to minimize GPS holdover events — improving antenna installation location insure clear skyuse high gain profile antenna It’s a community-based project which helps to repair anything.

It is important to design carefully the frequency allocations and potential bands e. Specifically when operating a dual-carrier BTS e.

When operating with DHCP option 66 and 67, the CPE might not receive an IP if option 67 is not used only 66 or extteme the option 67 xml file is not at the specified location.

  EONNAS PRO 800 PDF

BreezeMAX® Extreme 5000

CSassociate to it the forwarding rule you’ve created in step ‘b’. When using forwarding with option 82, if the Service Group gateway is a Cisco router the following configuration must be add on the Cisco to permit the DHCP packets to pass: This service profile aims to optimize the air link performance attuned to the video content optimized for MPEG In order to downgrade to release 1.

As part of these changes, several additional configuration options are available, such as: Any service modification requires MS de-registration in order to take place. When running Spectrum Analyzer while operating in dual sector mode, if system had developed misssynchronization because of GPS holdover, at the end of the scan process the system would reinitialize both channels.

Ping messages of bytes transmitted over R1 to the host behind CPE are sometimes unanswered. When BTS is operating with Release 1.

If static routes are added to a device acting as DHCP client the routed classes will not perform traffic. Two breezenax flows which have the same priority are equalized by the CPE at packet rates and not bit rates the packet sizes are not taken into account. The following is a general description: De-register the MS to have the new setting in affect